Product List
Home » Products » Roll Forming Machine » Corrugated Sheet Forming Machine

Corrugated Sheet Forming Machine

Flat Sheet Roll Forming Machine
No. Item Qty.
1 Passive de-coiler 1 piece
2 Roll forming machine 1 piece
3 Hydraulic cutting blade 1 set
4 Hydraulic station 1 piece
5 Computer control counter 1 piece
6 Run out table 3 pieces

Profile drawing

Main parameter
1. De-coiler: manual operation, passively de-coiling
2. Loading of de-coiler: 5 T
3. Frame of machine: welded with 350H beam steel
4. Guide feeding way of forming: side direction roller type
5. Forming machine type: wallboard and chain drive
6. Diameter of shaft: ¢76mm
7. Chain: 16A single row
8. Motor power of forming machine: 5.5KW
9. Line speed of forming machine: 5-17m/min
10.Steps of forming machine: 18
11.Roller material: superior 45# steel forging
12.Thickness of Chrome plated on roller: 0.05mm
13.Hydraulic station motor: 4 KW
14.Hydraulic station oil pump: gear pump
15.Cutting way: cut off after hydraulic shaped
16.Cutting blade material: Cr12
17.Cutting blade heat treatment: HRC58º-60
18.Rolling thickness: 0.4-0.8 mm
19.Feeding width: 1250mm
20. Precision of cut-to-length: ±2mm
21.Frequency changer : Panasonic
22.Computer adopts PLC : Panasonic
23. Dimension of machine: 8.5M x 1.6M x 0.8M

Technological process
Passively de-coiling → Guiding & Feeding material → Roll Forming →Cutting-to-length → Output panel

Technological process figure

Corrugated Sheet Roll Forming Machine

Flat Sheet Roll Forming Machine

Main parameter
1.Type of drive: gear motor drive
2.Diameter of shaft: ø200mm
3.Motor power of the corrugated sheet roll forming machine: 5.5kW
4.Line speed of this corrugated sheet roll former: 9-12times/min
5.Rolling thickness: 0.6-1.0mm
6.Feeding material width: 1300mm
7.Feeding material length: 2200mm
8.Voltage: 380V, 50Hz, 3 phase
9.Capacity: 2-4ton/hour
10.Machine size: 4300 × 2000 × 1500mm
11.Machine weight: 5.6ton

Profile drawing

Machine Picture
Related products
  • Edging&Beading Machine Short introduction:controlled by PLC,hydraulic drive
    Main technics: a)Beading height:≤14mm
    B) Drum height:894-905(mm). c) Hydraulic system pressure:8Mpa
    d) Air pressure:0.1Mpa . E) Machine size:3700x700x1600(mm),Total weight: 5T...
  • 1000-610 Construction MachineryMain Technical Specifications of 1000-610 Construction Machinery:
    Size: 11200mm × 2230mm × 2300mm.Total Weight: about 15000KG
    Total MotorPower:17.9KW
    Bending Power: 3.0kw+1.1kw×2 Seaming Power: 2.2kw....
  • C Shaped Steel Purlin Forming Machine1. All the rollers are forged from the high quality structural steel and are processed intensely. The surfaces of the rollers are plated with hard chromium, which lengthens the operating life of rollers. 2. The computer controls the length, punching and counting. 3. There are the flattening rollers at the front end of the machine, which are used for flattening the strip steel with poor flatness. After flattening....
  • Lipp-SM40 Spiral Steel Silo Forming MachineWorking Process of Spiral Steel Silo Forming Machine:
    Through 5 forming and 5 buckling procedures of Rx4.0m/m steel strip forming machine (thickness:2-4mm, width: 495mm), the steel strips will be merged forcedly and sutured spirally into circular cylinders with different diameters (4-50m)...
  • Flat Sheet Bending MachineTechnical Parameters of Flat Sheet Bending Machine:
    Main Motor Power:4kw
    Hydraulic Power:3KW
    Hydraulic Oil Pump:CB-E310 ...